Mirzo Ulug‘bek
tumani, Mirzo Ulug‘bek shoh ko‘chasi, 25-uy
Mirzo Ulug‘bek
tumani, Mirzo Ulug‘bek shoh ko‘chasi, 25-uy
The upper valley is a roofing element in the form of an internal corner, located at the junction of the roof slopes.
Internal corner plank used to finish the internal corners of the facade of the building, mainly at the junction of walls and roofs.
A simple docking bar closes the joints of profiled sheets along the entire length, protects against loosening of fasteners and sheets being torn off by gusts of wind
The window trim is a special element designed to finish the slopes and hide the cut edges of the panels.
The inner corner plank used for finishing the inner corners of the facade of the building has a decorative functional component, which gives an aesthetic and attractive appearance to the joints of various corrugated boards at the corners, while ensuring competent and reliable sealing of the joint. It is mainly used at the junction of walls and roofs, chimneys and roofs.
The starting or initial siding bar is the element from which the wall cladding begins. It is installed with the top edge along a pre-marked horizontal line located 40 mm above the bottom border of the trim. Subsequently, the siding panel is inserted into the starting bar with its lower edge, and the upper edge is attached to the wall or crate.
The end strip, thanks to polymerization and attractive appearance, creates an impeccable aesthetic and beautiful design for the facade of the building, protecting the roof from wind load, moisture, etc.
A simple low tide is a bar that is installed from the outside of the building to provide protection from precipitation.
The front plate protects the front board from moisture and serves as an additional support for the drain clamps and the filing of the cornice part of the roof. It is fastened before installing the cornice strip with self-tapping screws with a pitch of 35–40 cm and an overlap of at least 5 cm.
The outer corner bar acts as a decorative element that gives an aesthetic appearance to the joints.
Ridge bar – single-pitched roof is designed to protect the upper horizontal edge of the roof from precipitation and is used in cases where corrugated board or metal tile acts as a roofing material.
Snow retention strip – used for installation on pitched roofs of all types
Flat ridge strip – used for roofing of private housing construction. Made from high strength material. Does not corrode.
Snow retention strip – used for installation on pitched roofs of all types
Roof strip – used to frame skylights on the roof, protecting them from falling precipitation flowing down the roof.
Flat skate – used in the construction of the roof to protect the junction of the roof slopes from moisture or snow getting under the roof.
The ridge bar is fastened with roofing screws to a profiled sheet or metal tile.
Also, such a ridge performs a decorative function, giving the roof a finished appearance.
Ridge strip – is an additional roof element that protects the upper horizontal edge of the roof, formed by the intersection of two or more roof slopes from rainwater. Fix the bar should be on top of the sheets of metal.
Parapet covers – products made of thin sheet galvanized steel / steel with a polymer coating, used for protection
П-shaped strips – for fences made of corrugated board and metal picket fences are installed along the upper edge of the fence in order to protect them from atmospheric moisture and corrosion.
Parapet covers – products made of thin sheet galvanized steel / steel with a polymer coating, used for protectionv
Drip bar – The main function of the dripper is the safe removal of water (rain, melt, dew) from the roof, protection of the frontal cornice board from moisture penetration during heavy precipitation. As a result, the bar protects against moisture ingress into the under-roof space.
Upper valley – is a roofing element in the form of an internal corner, located at the junction of roof slopes.
Adjacency bar – is necessary to make the junction of the roof corner to the wall. It is installed on that section of the roof, which is formed with the help of a roof with a wall or a pipe.
The lower valley – is an important element in the construction of any house, which ensures the tightness of the water flow in the groove – an element at the junction of two slopes that form a gutter. Fastened with roofing screws at the extreme points from the center.
near-window strip – used to protect windows from moisture and condensation. Also, this product gives the windows a finished and decorated look.
Adjacency bar – is necessary to make the junction of the roof corner to the wall. It is installed on that section of the roof, which is formed with the help of a roof with a wall or a pipe.
Adjacency bar – is necessary to make the junction of the roof corner to the wall. It is installed on that section of the roof, which is formed with the help of a roof with a wall or a pipe.
